U-Boot 1.1.3 (Dec 26 2012 - 17:31:39) Board: Ralink APSoC DRAM: 32 MB relocate_code Pointer at: 81fb4000 sysctl:40200300 spi_wait_nsec: 42 spi device id: ef 40 17 0 0 (40170000) find flash: W25Q64BV raspi_read: from:30000 len:1000 .raspi_read: from:30000 len:1000 .============================================ Ralink UBoot Version: 3.5.3.0 -------------------------------------------- ASIC 5350_MP (Port5<->None) DRAM_CONF_FROM: Boot-Strapping DRAM_TYPE: SDRAM DRAM_SIZE: 256 Mbits DRAM_WIDTH: 16 bits DRAM_TOTAL_WIDTH: 16 bits TOTAL_MEMORY_SIZE: 32 MBytes Flash component: SPI Flash Date:Dec 26 2012 Time:17:31:39 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:128, ways:4, linesz:32 ,total:16384 ##### The CPU freq = 360 MHZ #### estimate memory size =32 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 . Image Name: Linux Kernel Image Created: 2013-03-20 13:21:26 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4083648 Bytes = 3.9 MB Load Address: 80000000 Entry Point: 802f9000 raspi_read: from:50040 len:3e4fc0 ............................................................... Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 802f9000) ... ## Giving linux memsize in MB, 32 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.21 (root@mailzxh-desktop) (gcc version 3.4.2) #700 Wed Mar 20 21:21:21 CST 2013 The CPU feqenuce set to 360 MHz CPU revision is: 0001964c Determined physical RAM map: memory: 02000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 8128 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 16kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). Cache parity protection disabled cause = c0808000, status = 11000000 PID hash table entries: 128 (order: 7, 512 bytes) calculating r4koff... 00057e40(360000) CPU frequency 360.00 MHz Using 180.000 MHz high precision timer. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 29220k/32768k available (2647k kernel code, 3548k reserved, 392k data, 124k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: MIPS clocksource has been installed. IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered deice id : ef 40 17 0 0 (40170000) W25Q64BV(ef 40170000) (8192 Kbytes) mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 8 MTD partitions on "raspi": 0x00000000-0x00800000 : "ALL" 0x00000000-0x00030000 : "Bootloader" 0x00030000-0x00040000 : "Config" 0x00040000-0x00050000 : "Factory" 0x00050000-0x00150000 : "Kernel" 0x00150000-0x00480000 : "RootFS" 0x00480000-0x00780000 : "sys" 0x00780000-0x00800000 : "param" Load Ralink DFS Timer Module RT3xxx EHCI/OHCI init. squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered (default) gpiomode:404055 addr:b0000000 by zqh gpiomode:404059 by zqh1 Ralink gpio driver initialized Enable Ralink GDMA Controller Module GDMA IP Version=2 i2cdrv_major = 218 HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 N_HDLC line discipline registered. Ralink APSoC Hardware Watchdog Timer Serial: 8250/16550 driver $Revision: 1.7 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A loop: loaded (max 8 devices) rdm_major = 254 Ralink APSoC Ethernet Driver Initilization. v2.1 256 rx/tx descriptors allocated, mtu = 1500! NAPI enable, weight = 32, Tx Ring = 256, Rx Ring = 256 MAC_ADRH -- : 0x0000000a MAC_ADRL -- : 0xebb109df PROC INIT OK! PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 PPPoL2TP kernel driver, V0.17 PPTP driver version 0.8.1 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky Linux video capture interface: v2.00 usbcore: registered new interface driver uvcvideo USB Video Class driver (SVN r209) block2mtd: version $Revision: 1.1.1.1 $ usbmon: debugfs is not available rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC). ALSA device list: No soundcards found. nf_conntrack version 0.5.0 (256 buckets, 131072 max) ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 NET: Registered protocol family 17 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 124k freed init started: BusyBox v1.12.1 (2013-03-02 13:26:40 CST) starting pid 16, tty '': '/etc_ro/rcS' Algorithmics/MIPS FPU Emulator v1.5 devpts: called with bogus options drivers/usb/core/inode.c: usbfs: unrecognised mount option "defaults" or missing value drivers/usb/core/inode.c: usbfs: mount parameter error: Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= gpio open ralink gpio release by zqh clr gpio starting pid 32, tty '/dev/ttyS1': '/bin/sh' BusyBox v1.12.1 (2013-03-02 13:26:40 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. # Started WatchDog Timer. zqh socket fd=3 zqh bind(6666) address successful! zqh socket fd=3 zqh bind(6666) address successful! InitSystemParam 0 =========================read system param from file================================== mac:00:6E:07:9B:7C:1C 30 wifimac:00:6E:07:9B:7C:1D 30 wifimac:00:6E:07:9B:7C:1D ie param ppid 36 ie param ppid 39 daemon:===== wifi.c, line 71, WifiConfig(): SSID=ChinaNet daemon:===== wifi.c, line 347, WifiDriversInit(): insmod From kernal rt2860v2_sta: module license 'unspecified' taints kernel. === pAd = c0095000, size = 534784 === <-- RTMPAllocAdapterBlock, Status=0 daemon:===== wifi.c, line 355, WifiDriversInit(): [insmod /lib/modules/2.6.21/kernel/drivers/netRX DESC a1da3000 size = 2048 /wireless/rt2860v2_sta/rt2860v2_sta.ko mac=00:6E<-- RTMPAllocTxRxRingMemory, Status=0 :07:9B:7C:1D] OK Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 9 2. Phy Mode = 9 3. Phy Mode = 9 MCS Set = ff 00 00 00 01 <==== rt28xx_init, Status=0 0x1300 = 00064300 EthMacInit2 EthMacInit3 phy_tx_ring = 0x01fa8000, tx_ring = 0xa1fa8000 phy_rx_ring0 = 0x01fa9000, rx_ring0 = 0xa1fa9000 MAC_ADRH -- : 0x0000006e MAC_ADRL -- : 0x079b7c1c RT305x_ESW: Link Status Changed EthMacInit4 switch reg write offset=14, value=5555 switch reg write offset=40, value=1001 switch reg write offset=44, value=1001 switch reg write offset=48, value=1001 switch reg write offset=4c, value=1 switch reg write offset=50, value=2001 switch reg write offset=70, value=ffffffff switch reg write offset=98, value=7f7f switch reg write offset=e4, value=7f done. EthMacInit5 EthMacInit5 switch reg write offset=14, value=5555 switch reg write offset=40, value=1001 switch reg write offset=44, value=1001 switch reg write offset=48, value=1001 switch reg write offset=4c, value=1 switch reg write offset=50, value=2001 switch reg write offset=70, value=ffffffff switch reg write offset=98, value=7f7f switch reg write offset=e4, value=7f done. eth is start =====InitNetDrivers======= ======dns failed===========: pid 29 NetThreadProc netstatsem post Daemon...=======network change======= Daemon...netok -1 link 0 net is work on wifi enter dhcp mode route: ioctl 0x890c failed: No such process killall: udhcpc: no process killed Ethnet Dhcp udhcpc (v1.12.1) started netstatsem post end start app update thread start sys update thread =======mac======= 00-6e-07-9b-7c-1c- No lease, failing zqh socket fd=7 zqh bind(9123) address successful! ipc param ppid 33 update socket init update Socket proc is start system param init =========================read system param from file================================== mac:00:6E:07:9B:i2s enable:1 7C:1C 30 wifimawork in slave audiohw_preinit by zqh 12Mhz c:00:6E:07:9B:7Cgpio open :1D 30 wifimac:00:6E:07:9B:7C:1D sys_ver 570840a5 audio init dhcp is start...=0 dhcp is stop... wifistart1 route: ioctl 0x890c failed: No such process wifistart2 wifistart3 wifistart4 wifistart5 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/encrypt.c, line 689, CheckAudioChip :iRet=0, rdat=0x00 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/encrypt.c, line 699, CheckAudioChip :=============Audio Chip = ES8388S!!!!!! ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/encrypt.c, line 786, CheckAudioChip :@@@@@@@@@@@@@@@@@@@@Init 8388s @@@@@@@@@@@@@@@@@@@@@ ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/encrypt.c, line 794, CheckAudioChip :write i2c not ack ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/encrypt.c, line 800, CheckAudioChip :Init 8388s over ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/encrypt.c, line 881, CheckAudioChip :=============Audio Chip isn't exist... --------------SaveSystemParam---------- bparam.stNetParam.szIpAddr = 192.168.1.100 link:0 status:0 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 1822, ReadVertSteps :Read maxverttime = 170 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 1874, GetVertTime :get vertime 163 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 1537, ReadLevelSteps :Read maxleveltime = 510 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 1589, GetLevelTime :get levelime 163 zqh socket fd=11 zqh bind(8832) address successful! zqh socket fd=12 zqh bind(6666) address successful! zqh socket fd=13 zqh bind(8832) address successful! /SUPRA/ =============================================================== /SUPRA/ supra Unified IPC Firmware /SUPRA/ Core built Feb 25 2016 14:00:32 /SUPRA/ =============================================================== /SUPRA/ Runtime feature flags: /SUPRA/ SD.......: ENABLED /SUPRA/ HD.......: ENABLED /SUPRA/ Record...: DISABLED /SUPRA/ Discovery: DISABLED /SUPRA/ MegraCloud device class: /SUPRA/ IPC02 /SUPRA/ =============================================================== /SUPRA/ (C) 2013-2015 SUPRA Foto-Elektronik-Vertriebs-GmbH /SUPRA/ =============================================================== /SUPRA/ Initializing config ... Socket proc is start pid=154 /SUPRA/ Config initialized successfully. /SUPRA/ Initializing local recorder ... /SUPRA/ Local recorder initialized. /SUPRA/ Initializing MegraCloud ... /SUPRA/ MegraCloud initialized successfully. /SUPRA/ Initializing alarm ... /SUPRA/ Alarm initialized successfully. /SUPRA/ Initializing periodic ... /SUPRA/ Periodic initialized successfully. /SUPRA/ Initializing AV ... /SUPRA/ AV initialized successfully. /SUPRA/ Initializing web ... ie param ppid 133 /SUPRA/ Running periodic NTP update ... /SUPRA/ Web initialized. /SUPRA/ Initializing discovery ... /SUPRA/ Discovery initialized. /SUPRA/ supra Unified IPC Firmware running. Set: phy[0].reg[0] = 3900 Set: phy[1].reg[0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 ESF: PRE Set: phy[4].reg[4] = 0461 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 413, H264SetIRCutMode : waiting ait 8433 init over ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 856, CheckIRCutStatus :change to normal /SUPRA/ NTP update error: 'Transport failed' /SUPRA/ Running periodic UPNP update ... Set: phy[4].reg[0] = b100 TF: consecutive run. ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 5046, GpioStatusLed :motofd = 10, portvalue = 00e06807 upnpc : miniupnpc library test client. (c) 2006-2010 Thomas Bernard Go to http://miniupnp.free.fr/ or http://miniupnp.tuxfamily.org/ for more information. ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 5046, GpioStatusLed :motofd = 10, portvalue = 00e05807 usb 1-1: new high speed USB device using rt3xxx-ehci and address 2 usb 1-1: configuration #1 chosen from 1 choice Found format YUV 4:2:2 (YUYV). - 640x480 (30.0 fps) - 160x120 (30.0 fps) - 320x240 (30.0 fps) - 640x360 (30.0 fps) - 384x216 (30.0 fps) - 352x288 (30.0 fps) - 1280x720 (30.0 fps) - 960x720 (30.0 fps) - 800x448 (30.0 fps) - 800x600 (30.0 fps) - 160x90 (30.0 fps) - 320x180 (30.0 fps) Found format MJPEG. - 640x360 (30.0 fps) - 160x120 (30.0 fps) - 320x240 (30.0 fps) - 640x480 (30.0 fps) - 384x216 (30.0 fps) - 352x288 (30.0 fps) - 1280x720 (30.0 fps) - 960x720 (30.0 fps) - 1024x576 (30.0 fps) - 800x448 (30.0 fps) - 800x600 (30.0 fps) - 160x90 (30.0 fps) - 320x180 (30.0 fps) uvcvideo: Unknown video format 34363248-0000-0010-8000-00aa00389b71 Found format 34363248-0000-0010-8000-00aa003. - 1280x720 (30.0 fps) - 640x480 (30.0 fps) - 320x240 (30.0 fps) - 160x120 (30.0 fps) - 160x90 (30.0 fps) - 320x180 (30.0 fps) - 640x360 (30.0 fps) - 480x270 (30.0 fps) - 800x450 (30.0 fps) - 1024x576 (30.0 fps) uvcvideo: Found UVC 1.00 device (114d:8433) uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Enabling workaround. input: UVC Camera (114d:8433) as /class/input/input0 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 1251, H264GetSupportFormat : 0. YUV 4:2:2 (YUYV) ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 1251, H264GetSupportFormat : 1. MJPEG ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 1251, H264GetSupportFormat : 2. 34363248-0000-0010-8000-00aa003 **AIT DEBUG**:: AitXU_Init **AIT DEBUG**:: AitXU_Init: open devive /dev/video0. **AIT DEBUG**:: AitXU_Init **AIT DEBUG**:: AitXU_Init: Add XU controls. **AIT DEBUG**:: AitXU_Init: mapping XU controls. Add XU: Set ISP XU Mapping err = 0 XU Mapping err = 0 Add XU: Get ISP XU Mapping err = 0 XU Mapping err = 0 Add XU: Set MMP XU Mapping err = 0 XU Mapping err = 0 Add XU: Get MMP XU Mapping err = 0 XU Mapping err = 0 Add XU: Set MMP16 XU Mapping err = 0 XU Mapping err = 0 Add XU: Get MMP16 Result XU Mapping err = 0 XU Mapping err = 0 Add XU: Set ISP EX XU Mapping err = 0 XU Mapping err = 0 Add XU: Get ISP EX Result XU Mapping err = 0 XU Mapping err = 0 Add XU: Get MMP MEM XU Mapping err = 0 XU Mapping err = 0 Add XU: Set MMP MEM XU Mapping err = 0 XU Mapping err = 0 **AIT DEBUG**:: AitXU_Init: OK. 2.6 XU Cmd ret = 0 2.6 XU Cmd ret = 0 2.6 XU Cmd ret = 0 2.6 XU Cmd ret = 0 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 806, H264GetFwVersion : Firmware build day: 2015.Dec.23 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 810, H264GetFwVersion : Firmware ver: 1.0.1223 **AIT DEBUG**:: SkypeXU_SetMode 2.6 XU Cmd ret = 0 **AIT DEBUG**:: SkypeXU_SetEncRes 2.6 XU Cmd ret = 0 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 176, GetParamDefault : cur=128 Max=255, Min=0, Step=1 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 176, GetParamDefault : cur=128 Max=255, Min=0, Step=1 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 176, GetParamDefault : cur=128 Max=255, Min=0, Step=1 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 176, GetParamDefault : cur=0 Max=180, Min=-180, Step=1 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 982, ConfigureDev : req.count: 3 **AIT DEBUG**:: AitXU_SetFrameRate 2.6 XU Cmd ret = 0 2.6 XU Cmd ret = 0 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/video/video.c, line 145, SetVideoParamInit :bparam.stVencParam.videomode = 0 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 383, H264SetMirr : before mirrflip=0 2.6 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 4711, MotoCentProc :=====moto is start===== ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 4712, MotoCentProc :moto start, read moto sit ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 4713, MotoCentProc :presend = 0, speed = 5 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 283, ReadMotoSit :create failed ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 4720, MotoCentProc :Set Moto to Center----- ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 4727, MotoCentProc :=============center_prefab_flag = 2 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/moto-new.c, line 4756, MotoCentProc :===========save sit XU Cmd ret = 0 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/h264/8433/vienc.c, line 377, SetMirrFlip : after mirrflip=0 2.6 XU Cmd ret = 0 ===AitXU_SetBitrate(2048)=== **AIT DEBUG**:: AitXU_SetBitrate 2.6 XU Cmd ret = 0 Power Line Frequency=2 Max=2, Min=0, Step=1 [0]Auto, [2]50Hz, [1]60Hz write 5020 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/func/main.c, line 71, main :SystemVerion==================[ 87.8.64.165 ]============== write 5020 get main thread param --------------SaveSystemParam---------- bparam.stNetParam.szIpAddr = 192.168.1.100 ==== /home/stefanschadt/Desktop/IPCam/Firmware/Target/RT5350/HD/network/ipc.c, line 427, NetThreadproc :Wifi Change, Recv Daemon Sync(2), bparam.stNetParam.szIpAddr = 192.168.1.100, New = 192.168.1.100 sys_ver 570840a5 get main thread param No IGD UPnP Device found on the network ! upnpc : miniupnpc library test client. (c) 2006-2010 Thomas Bernard Go to http://miniupnp.free.fr/ or http://miniupnp.tuxfamily.org/ for more information. def key proc No IGD UPnP Device found on the network ! /SUPRA/ Periodic UPNP update completed. /SUPRA/ Running periodic time backup ... /SUPRA/ Periodic time backup completed. # id /bin/sh: id: not found # cat /proc/cpuinfo system type : Ralink SoC processor : 0 cpu model : MIPS 24K V4.12 BogoMIPS : 239.10 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : yes ASEs implemented : mips16 dsp VCED exceptions : not available VCEI exceptions : not available # cat /proc/meminfo MemTotal: 29344 kB MemFree: 12748 kB Buffers: 1024 kB Cached: 4516 kB SwapCached: 0 kB Active: 2140 kB Inactive: 4428 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 1056 kB Mapped: 3212 kB Slab: 4572 kB SReclaimable: 532 kB SUnreclaim: 4040 kB PageTables: 188 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 14672 kB Committed_AS: 3092 kB VmallocTotal: 1048404 kB VmallocUsed: 4336 kB VmallocChunk: 1042720 kB # mount rootfs on / type rootfs (rw) /dev/root on / type squashfs (ro) proc on /proc type proc (rw) none on /var type ramfs (rw) none on /etc type ramfs (rw) none on /tmp type ramfs (rw) none on /media type ramfs (rw) none on /sys type sysfs (rw) none on /dev/pts type devpts (rw) none on /proc/bus/usb type usbfs (rw) /dev/mtdblock6 on /system type jffs2 (rw) /dev/mtdblock7 on /param type jffs2 (rw) # df Filesystem 1k-blocks Used Available Use% Mounted on rootfs 3008 3008 0 100% / /dev/root 3008 3008 0 100% / /dev/mtdblock6 3072 1880 1192 61% /system /dev/mtdblock7 512 244 268 48% /param # ps PID USER VSZ STAT COMMAND 1 root 1484 S init 2 root 0 SWN [ksoftirqd/0] 3 root 0 SW< [events/0] 4 root 0 SW< [khelper] 5 root 0 SW< [kthread] 6 root 0 SW< [kblockd/0] 7 root 0 SW< [khubd] 8 root 0 SW< [kswapd0] 9 root 0 SW [pdflush] 10 root 0 SW [pdflush] 11 root 0 SW< [aio/0] 12 root 0 SW< [scsi_tgtd/0] 13 root 0 SW [mtdblockd] 14 root 0 SW< [kmmcd] 20 root 1092 S nvram_daemon 23 root 0 SWN [jffs2_gcd_mtd6] 25 root 0 SWN [jffs2_gcd_mtd7] 29 root 1696 S /system/system/bin/daemon.v5.12 30 root 1480 S /system/system/bin/cmd_thread 31 root 1480 S /system/system/bin/gmail_thread 32 root 1488 S /bin/sh 33 root 1696 S /system/system/bin/daemon.v5.12 36 root 1480 S /system/system/bin/cmd_thread 39 root 1480 S /system/system/bin/gmail_thread 40 root 1696 S /system/system/bin/daemon.v5.12 41 root 1696 S /system/system/bin/daemon.v5.12 44 root 1480 S /system/system/bin/cmd_thread 45 root 1480 S /system/system/bin/gmail_thread 50 root 0 SW [RtmpCmdQTask] 51 root 0 SW [RtmpWscTask] 89 root 1696 S /system/system/bin/daemon.v5.12 115 root 1696 S /system/system/bin/daemon.v5.12 116 root 1696 S /system/system/bin/daemon.v5.12 117 root 1696 S /system/system/bin/daemon.v5.12 124 root 1696 S /system/system/bin/daemon.v5.12 125 root 1696 S /system/system/bin/daemon.v5.12 126 root 1696 S /system/system/bin/daemon.v5.12 130 root 5896 S /system/system/bin/encoder 133 root 5896 S /system/system/bin/encoder 134 root 5896 S /system/system/bin/encoder 135 root 5896 S /system/system/bin/encoder 152 root 5896 S /system/system/bin/encoder 153 root 5896 S /system/system/bin/encoder 154 root 5896 S /system/system/bin/encoder 155 root 5896 S /system/system/bin/encoder 156 root 5896 S /system/system/bin/encoder 157 root 5896 S /system/system/bin/encoder 158 root 5896 S /system/system/bin/encoder 159 root 5896 S /system/system/bin/encoder 160 root 5896 S /system/system/bin/encoder 163 root 5896 S /system/system/bin/encoder 164 root 5896 S /system/system/bin/encoder 165 root 5896 S /system/system/bin/encoder 166 root 5896 S /system/system/bin/encoder 167 root 5896 S /system/system/bin/encoder 168 root 5896 S /system/system/bin/encoder 169 root 5896 S /system/system/bin/encoder 170 root 5896 S /system/system/bin/encoder 185 root 5896 S /system/system/bin/encoder 188 root 5896 S /system/system/bin/encoder 189 root 5896 S /system/system/bin/encoder 227 root 1484 R ps # [ inadyn radvd [[ init ralink_init accel-pptp.sh insmod reboot ash internet.sh reg ated iptables ripd autoconn3G.sh iwconfig rm automount.sh iwlist rmmod brctl iwpriv route busybox kill rt2860apd cat killall rtinicapd chmod klogd sed chpasswd lan.sh setuidgid chpasswd.sh lld2d sh config-dns.sh ln sleep config-iTunes.sh logger snmp.sh config-igmpproxy.sh login snort.sh config-l2tp.sh logread switch config-pppoe.sh ls sync config-pptp.sh lsmod sysctl config-udhcpd.sh lsusb syslogd config-vlan.sh mii_mgr tc config.sh mkdir telnetd cp mkdosfs test cpubusy.sh mount tftp date mtd_write top ddns.sh mv touch df nat.sh udhcpc dmesg netstat udhcpc.sh dnsmasq network.sh udhcpd dos2unix ntp.sh umount echo nvram_daemon unix2dos envuidgid nvram_get unzip eraseall nvram_set update expr openl2tp.sh upnp_xml.sh fdisk openl2tpd upnpd firewall.sh openssl uptime free pidof usleep g++-uc ping uvc_stream global.sh poweroff vconfig gpio pppd vpn-passthru.sh halt pppoe-relay wan.sh i2scmd pppoe.sh wifi_unload.sh ifconfig ps wscd igmpproxy qos_portbased_run zebra igmpproxy.sh qos_run